ISW BIT1-HBX WLSN INSTALLATION TOOL
The wLSN Installation Tool is an alphanumeric liquid crystal display (LCD) keypad that works with the wLSN. Hub to assist the installer in evaluating the suitability of a particular site for the installation of wireless devices and for verifying the cceptability of specific locations for the placement of wireless devices. The installation tool has a two-line, 16-character text display and a sounder. The installation tool also has a green LED for indicating battery charging status. The installation tool comes with a plug-in transformer and two docking stations: one for wall mounting; the other is a desktop cradle.
Functions:
Diagnostic Modes
Use the wLSN Installation Tool as a pre-installation tool for determining the suitability of a particular site for wireless applications or to validate individual device RF performance prior to permanent mounting. In other words, the wLSN Installation Tool provides assurance that a device installed at the chosen location can communicate reliably with the wLSN Hub. The wLSN Installation Tool has three user-selectable modes:
1. Go/No Go: indicates whether or not the tool is receiving a signal from the wLSN Hub of sufficient strength to ensure reception by a wireless device located at that site.
2. Packet Success Rate: indicates signal strength by the number of bars shown and the number of packets received by the tool (three packets are sent from the wLSN Hub every four seconds). The best location for placing a device is the one showing the highest number of bars and packets received.
3. Signal-to-Noise Ratio: provides separate readings for received signal strength, ambient noise level, and signal-to-noise ratio. The higher the signal-to-noiseratio; the better the location. Fixed Operation When placed into a docking station, the wLSN Installation Tool is powered from the docking station through a cable and wall transformer. While the tool is in the docking station, the batteries are automatically recharged. The green status LED on the tool indicates the charging status of the batteries whenever the tool is in the docking station:
- Continuously on indicates fully-charged batteries
- Slow flashing indicates batteries are being recharged
- Off indicates the install
Technical Specifications
- Environment: Indoor, dry
- EN50131-1: Environmental Class II
- Relative Humidity: Up to 95%, non-condensing
- Temperature (operating): -10°C to +55°C (+14°F to +131°F)
Mechanical Properties
- Color: Off-white
- Dimensions (H x W x D): 12.6 cm x 7.5 cm x 4.5 cm (5.0 in. x 3.0 in. x 1.8 in.)
- Power Requirements: Battery Power
- Battery Life: Up to 50 hr of continuous use on a singlecharge.
- Battery Requirements: Three AAA nickel-metal hydride (NiMH) rechargeable batteries
- Recommended Replacements:SANYO® HR-AAAU Recharge Time: Requires 7 hr to recharge fully depletedbatteries
- External Power Supply (Docking Module)
- Voltage (supply): 6 VDC to 14 VDC
- Reception Characteristics Frequency: European Security Band 868 MHz to 869 MHz
Transformers
- All Transformer Models Current (output): 0.33 A
- Power: 8 W
- Voltage (output): with load: 9.0 VDC ± 5%
- ISW-BIT1-HAX (United Kingdom Transformer)
- Frequency: 50 Hz
- Voltage (input): 230 VAC to 240 VAC
- Voltage (output): without load: 15.0 VDC ± 5% ISW-BIT1-HBX (European Transformer)
- Frequency: 50 Hz
- Voltage (input): 230 VAC to 240 VAC
- Voltage (output): without load: 16.5 VDC ± 5% ISW-BIT1-HCX (United States Transformer)
- Frequency: 60 Hz
- Voltage (input): 120 VAC
- Voltage (output): without load: 13.5 VDC ± 5